• Click here to access some of the presentations made during the 2022 National Rally

2025 Paradigm 385FL New Owners

Lenyaw2877

Lenyaw2877

New member
We detoured from Rapid City SD to Lake Park GA on our way to Columbia SC to trade in our 5 month old Grand Design Momentum 415G piece of junk.
We are full-timers for the past 5 years & this is our 4th RV.
After finally getting things put into place & partially organized in the past 2 weeks, we are really enjoying our new Paradigm.
Glad to be part of the Alliance family.
 
BryanValRox

BryanValRox

Well-known member
Lenyaw2877 said:
We detoured from Rapid City SD to Lake Park GA on our way to Columbia SC to trade in our 5 month old Grand Design Momentum 415G piece of junk.
We are full-timers for the past 5 years & this is our 4th RV.
After finally getting things put into place & partially organized in the past 2 weeks, we are really enjoying our new Paradigm.
Glad to be part of the Alliance family.
Click to expand...
Congratulations and welcome to the Alliance Family!
 
2 Allies

2 Allies

Well-known member
Congratulations and Welcome! We too have the '24 385FL as well. We love the floorplan and it has been great. I echo 7426TRISS, there was a time when they mis-wired the macerator but once we got it correct it has worked flawlessly. If you run into trouble with the level indicator on the macerator, you can disconnect the leads to the tank and that issue will be solved. We also got our pass thru doors adjusted at the National Rally, no more leaks.

Good luck and enjoy,
 
Lenyaw2877

Lenyaw2877

New member
2 Allies said:
Congratulations and Welcome! We too have the '24 385FL as well. We love the floorplan and it has been great. I echo 7426TRISS, there was a time when they mis-wired the macerator but once we got it correct it has worked flawlessly. If you run into trouble with the level indicator on the macerator, you can disconnect the leads to the tank and that issue will be solved. We also got our pass thru doors adjusted at the National Rally, no more leaks.

Good luck and enjoy,
Click to expand...
Macerator levels have been a major headache so far. Can you please provide more details on how to disconnect the leads. Thanks in advance.
 
2 Allies

2 Allies

Well-known member
Lenyaw2877,

assume yours is the Sanimarin macerator. The is a control module under the toilet area in the back left storage compartment. It has a little box built into the corner that comes off by removing a few screws along the base and I think the vertical backing board. Once you remove this corner cover you will see the module. You just need to remove the two wire that are attached to the 50% and 100% screws. See picture below.

I just taped the end of the wires separately and left them. Go and try your toilet before putting it all back. 10-15 min job. We have had no issues and has worked great. You just need to remember that if the tank is full and you flush the pump will send it anyway:)

Good luck,
 

Attachments

  • 20240531_143843.jpg
    20240531_143843.jpg
    259.2 KB · Views: 15
Lenyaw2877

Lenyaw2877

New member
2 Allies said:
Lenyaw2877,

assume yours is the Sanimarin macerator. The is a control module under the toilet area in the back left storage compartment. It has a little box built into the corner that comes off by removing a few screws along the base and I think the vertical backing board. Once you remove this corner cover you will see the module. You just need to remove the two wire that are attached to the 50% and 100% screws. See picture below.

I just taped the end of the wires separately and left them. Go and try your toilet before putting it all back. 10-15 min job. We have had no issues and has worked great. You just need to remember that if the tank is full and you flush the pump will send it anyway:)

Good luck,
Click to expand...
Thank you so much.

This worked to get shut off the Full indicator light.

I have requested the schematics & all diagrams pertaining to the level sensors from Alliance. Will see if they are willing to send them.
I've heard that getting electrical drawings is tough... but they had no problem sending me the plumbing layout diagrams.
 
7

7426TRISS

Well-known member
I asked for the wiring for the toilet, was given three different prints. Only the last print they sent corrected the problem.
 
You must log in or register to reply here.
Top